resource hub | Batten space ventilation for pitched roofs

Batten space ventilation for pitched roofs

Download our Technical Manual

Download a PDF version of this article.

 

Introduction

 

This technical update provides additional guidance relating to how the Functional Requirements can be satisfied in our Technical Manual. The Must Haves section below indicates the information we need and this is followed by guidance on how to it may satisfy our Functional Requirements.

 

Warranty stance

 

Batten spaces often need to be ventilated where there is potential for warm air to condensate and rot the battens out. Our stance is batten spaces should be ventilated for warm or cold pitched roofs where a LR (low resistance) underlay is used in combination with an impermeable roof covering.

 

Must haves

 

For warranty purposes we require the following:

  • Design details showing the ventilation strategy for the pitched roof to be in accordance with our Technical Manual and BS5250 and;
  • Third-party product conformity certificate for any LR underlays used and;
  • Written confirmation and evidence must be sought from the manufacturer confirming the tiles/slates are considered air permeable or air impermeable as stipulated in BS 5250. Some tile manufacturers will not have this test information, in such cases we would assume worst case (that the tiles are air impermeable). For further information please see the ‘Other considerations’ section at the bottom of this article

 

Batten space ventilation to cold pitched roofs with LR underlay

 

Where air impermeable roof coverings are used with an LR underlay there is a risk of moisture accumulation on the underside of the outer weatherproof covering (within the batten space under the tiles). To reduce the risk of potentially damaging condensation, the batten space should be ventilated (see Figure 1). This should be achieved by means of counter battens and vents at both low and high level:

 

  • Low-level vents should be equivalent in free area to a slot 25 mm deep running the whole length of the eaves. Over-fascia vents should provide ventilation into the batten space
  • High-level vents should be equivalent in area to a slot 5 mm deep running the whole length of the ridge in accordance with BS5250
  • Eaves vent should also provide ventilation to the cold roof void as per BS5250

 

Note: Alternative methods of ventilating the batten void should provide an equivalent level of ventilation.

 

Barten space ventilation figure 1

 

Warm pitched roofs with LR underlay, an air and vapour control layer (AVCL) should be provided at ceiling line. Where an external covering (such as fibre cement slates) is air impermeable there is also a risk of interstitial condensation forming on the underside of the  underlay and the external covering, to avoid that risk the batten space should be ventilated as described above.

 

Batten space ventilation figure 2

 

 

Batten space ventilation to cold pitched roofs with High Resistance (HR) underlay

 

A  HR  underlay  provides  high  vapour  resistance  on  the  cold  side  of  the  thermal insulation, preventing the diffusion of water vapour from the loft in to the batten space; it is therefore essential that the loft space be ventilated in accordance with BS5250 and Section 11 of our Technical Manual.

 

Batten space ventilation to warm pitched roofs (insulation along the rafter pitch) with HR underlay

 

In warm roofs (with insulation along the rafter pitch) with an HR underlay, whatever form of external covering or ceiling is provided, there is a risk of interstitial condensation forming on the underside of the HR underlay. To avoid that risk, an AVCL should be provided on the warm side of the insulation, and ventilated voids should be formed between the underside of the underlay and the insulation.

 

Other considerations

 

Determining if the underlay is HR or LR

 

It is very difficult to determine a HR or LR underlay by sight alone and the manufacturer’s third party accreditation should be referred too.

 

Determining if the roof covering is air impermeable

 

As can be seen throughout this article, an important factor when determining if the batten space needs ventilation is if the roof covering you’ve chosen is air impermeable. For discontinuous roof coverings (tiles, slates etc) written confirmation and evidence must be sought from the manufacturer confirming the tiles/slates are considered air permeable or air impermeable as stipulated in BS 5250:

 

‘The air permeability of an outer weatherproof covering comprising discontinuous units may be determined by testing in accordance with BS 5534:2014+A2:2018, Annex L, using equipment capable of measuring pressure differences of 10 Pa.’

 

Some tile manufacturers will not have this test information, in such cases we would assume worst case (that the tiles are air impermeable).

 

Batten space ventilation for decorative cladding

 

This article has dealt with batten space ventilation for pitched roofs, however there should be consideration for providing a drained and vented cavity for decorative cladding on the external face of a masonry substrate. One way of achieving this is with the use of counter battens and a fly mesh at low and high level (to prevent insects getting inside the batten space).

 

Warranty position

 

As can be seen in the above article, the determining factors for batten space ventilation is if an LR underlay is chosen in combination with an impermeable roof covering. In these situations, batten space ventilation as per the above should be provided. Any deviation from the above should be in line with BS5250 and prior agreement must be sought from your warranty surveyor.

 

 


Read more articles on the Resource Hub and sign up to receive our blog round-up.

 

Every care was taken to ensure the information in this article was correct at the time of publication (March 2022). Guidance provided does not replace the reader’s professional judgement and any construction project should comply with the relevant Building Regulations or applicable technical standards. For the most up to date Premier Guarantee technical guidance please refer to your Risk Management Surveyor and the latest version of the Premier Guarantee Technical Manual.

Ref: TS 3138

Read more technical articles on our Resource Hub